ANALISA PENGARUH PENGGUNAAN VARIASI BESARAN ARUS AMPERE DAN TEKANAN GAS ARGON PADA PENGELASAN TUNGSTEN INERT GAS (TIG) TERHADAP KEKUTAN MEKANIK DAN PERUBAHAN STRUKTUR MIKRO

LINGGA, LINGGA (2018) ANALISA PENGARUH PENGGUNAAN VARIASI BESARAN ARUS AMPERE DAN TEKANAN GAS ARGON PADA PENGELASAN TUNGSTEN INERT GAS (TIG) TERHADAP KEKUTAN MEKANIK DAN PERUBAHAN STRUKTUR MIKRO. Skripsi thesis, Fakultas Teknik.

[img]
Preview
Text
BAB I & V.pdf - Published Version

Download (680kB) | Preview
[img]
Preview
Text (Akses versi ini dibuat terbatas untuk menghindari plagiasi. Silahkan menghubungi layanan referensi perpustakaan untuk mengakses file ini | [email protected])
BAB II - IV.pdf - Accepted Version

Download (1MB) | Preview

Abstract

The purpose of this study was to determine, knowing the strength of the tensile, tensile stress, and macro structure from the results of the analysis of the effect of using ampere current magnitude variations and Argon gas pressure in Tungsten inert gas welding (Tig), the two materials of tensile testing were 1422.89 N / mm2 has decreased from the testing of material one, the third test material experienced kenikan with a tensile stress value of 1428.77 N / mm2 with an average value of tensile stress testing 1427.58 N / mm2. using ampere 30 with 9000C heating even has a strength value that is greater than the strength of 25 ampere hardness with 9000C heating (59.6 HRC> 54, 4 HRC). 25 ampere welding voltage with 9000C heating smaller strength than welding 35 amperes and without heating 270C pull of 1474.94N / mm2 <1475.34 N / mm2, on the material of material 2 at 1470.66 N / mm2 <1472.44 N / mm2, in the material of the third material 3 shows almost the same value on the test results that is equal to 1473.22 N / mm2 <1473.32 N / mm2. using Ampere 35 with heating 900 0C in hardness testing as much as 61.3 HRC, without heating with a temperature of 27 0C, in testing the material 1 welding voltage 35 amperes with 9000C heating smaller than welding 35 amperes with no heating 270C average pull 1065.18 N / mm2 <1473.7 N / mm2, in the case of material 2 at 1064.43 N / mm2 <1472.44 N / mm2, the material of the third material 3 shows almost the same value in the test results which is equal to 1034 , 25 N / mm2 <1473.32 N / mm2, indicating the welding results depend on the ampere, Hardness by welding Argon Gas on Tungsten Inert Gas (Tig) welding with 35 amperes without heating 270C. Welding without heating up the initial material is only to facilitate the initial process of welding the material. // Tujuan penelitian ini adalah untuk mengetahui, Mengetahui kekuatan kekerasan, tegangan tarik, dan struktur makro dari hasil Analisa Pengaruh Penggunaan Variasi Besaran Arus Ampere Dan Tekanan Gas Argon Pada Pengelasan Tungsten Inert Gas (Tig), bahan pengujian dua nilai tengan tarik 1422,89 N/mm2 mengalami penurunan dari pengujian bahan satu, pada bahan pengujian ketiga mengalami kenaikan dengan nilai tegangan Tarik sebesar 1428,77 N/mm2 dengan nilai rata-rata pengujian tegangan tarik 1427,58 N/mm . menggunakan ampere 30 dengan pemanasan 900 2 C malahan memiliki nilai kekuatan kekerasan yang lebih besar jika dibandingkan dengan kekuatan kekerasan ampere 25 dengan pemanasan 900 0 C (59,6 HRC > 54,,4 HRC). tegangan pengelasan 25 ampere dengan pemanasan 900 0 C lebih kecil kekuatan nya dari pengelasan 35 ampere dangan tanpa pemanasan 27 0 , pada sempel bahan 2 pada 1470,66 N/mm 0 C tarik sebesar 1474,94N/mm 2 <1475,34 N/mm 2 , pada bahan sempel bahan ketiga 3 menunjukan nilai yang hampir sama pada hasil pengujian yaitu sebesar 1473,22 N/mm 2 < 1472,44 N/mm 2 . menggunakan Ampere 35 dengan pemanasan 900 2 < 1473,32 N/mm 2 C pada pengujian Kekerasan sebesar 61.3 HRC, tanpa pemanasan dengan suhu 27 0 C, pada pengujian sempel bahan 1 tegangan pengelasan 35 ampere dengan pemanasan 900 0 C lebih kecil kekuatan nya dari pengelasan 35 ampere dangan tanpa pemanasan 27 0 C tarik rata-rata sebesar 1065,18 N/mm 0 < 1472,44 N/mm 2 < 1473,7 N/mm 2 , pada sempel bahan 2 pada 1064,43 N/mm 2 , pada bahan sempel bahan ketiga 3 menunjukan nilai yang hampir sama pada hasil pengujian yaitu sebesar 1034,25 N/mm 2 < 1473,32 N/mm 2 2 , menunujukan hasil pengelasan tergantung pada ampere, Kekerasan dengan pengelasan Gas Argon Pada Pengelasan Tungsten Inert Gas (Tig) dengan ampere 35 tanpa pemanasan 270C. Pengelasan tanpa memanas material awal hanya untuk mempermudah proses awal pengelasan material.

Item Type: Thesis (Skripsi)
Uncontrolled Keywords: welding technique, welding machine, tensile test, hardness test, micro structure, and welding of argon gas in tungsten inert gas welding (Tig), nik Pengelasan, mesin Las, Uji Tarik, uji kekerasan, struktur micro, dan pengelasan Gas Argon Pada Pengelasan Tungsten Inert Gas (Tig)
Subjects: T Technology > TJ Mechanical engineering and machinery
Divisions: Fakultas Teknik > Prodi Teknik Mesin
Depositing User: S.IP., MA Dwi Cahyo Prasetyo
Date Deposited: 22 Dec 2020 02:33
Last Modified: 22 Dec 2020 02:33
URI: http://repository.unmuhpnk.ac.id/id/eprint/1218

Actions (login required)

View Item View Item